Description
Two component air drying aliphatic. Non Yellowing polyurethane finish coating.
Recommended Use
This product has excellent weathering resistance. It is recommended as topcoat with suitable primers and undercoats for use in High Chemical & Saline atmosphere for better aesthetics and common resistance. It is recommended for Chemical Plants, Off-shore & On –shore industries. Power Plants, Petrochemicals & Pharmaceutical Complexes, Cement & Steel Plants, Smelters, Transportation Industries, Infrastructure Projects Projects etc and also for premium OEM equipment painting.
Physical Data
𝐂𝐎𝐋𝐎𝐑 : Assorted shades𝐅𝐈𝐍𝐈𝐒𝐇 : Glossy / Semiglossy / Matt
𝐒𝐎𝐋𝐈𝐃𝐒 𝐁𝐘 𝐕𝐎𝐋𝐔𝐌𝐄 : 40 + 3% (Depends on shade)
𝐓𝐇𝐄𝐎𝐑𝐄𝐓𝐈𝐂𝐀𝐋 𝐒𝐏𝐑𝐄𝐀𝐃𝐈𝐍𝐆 𝐑𝐀𝐓𝐄 : 9 to 11 sq. mt./ltr. at a recommended DFT of 30 μ
𝐅𝐋𝐀𝐒𝐇 𝐏𝐎𝐈𝐍𝐓 : Base : Above 23® C Hardener : Above 23® C
𝐃𝐑𝐘𝐈𝐍𝐆 𝐂𝐇𝐀𝐑𝐀𝐂𝐓𝐄𝐑𝐈𝐒𝐓𝐈𝐂𝐒 : Surface Dry : 20 – 30 minutes
(At 65% relative humidity & at 30® C) Hard Dry : 4 hours Full Cure : 3 days
𝐒𝐇𝐄𝐋𝐋 𝐋𝐈𝐅𝐄 : Base : 6 months Hardener : 6 months
Surface Preperation
This being finish paint, it is a applied either over primer or Intermediate coat. The surface should be free from oil, moisture, dust and dirt. Aged coatings should be roughened by emery paper grade 400/600 for better bonding.
Application Data
𝐌𝐈𝐗𝐈𝐍𝐆 𝐑𝐀𝐓𝐈𝐎 : Base : Hardener – (As per our recommendations)𝐀𝐏𝐏𝐋𝐈𝐂𝐀𝐓𝐈𝐎𝐍 : By Brush / By Conventional Spray
𝐓𝐇𝐈𝐍𝐍𝐄𝐑 : Type 001
𝐏𝐎𝐓 𝐋𝐈𝐅𝐄 : 4 hours min at 30® C
𝐑𝐄𝐂𝐎𝐌𝐌𝐄𝐍𝐃𝐄𝐃 𝐃𝐅𝐓 : 30-40 µ.
𝐎𝐕𝐄𝐑𝐂𝐎𝐀𝐓𝐈𝐍𝐆 𝐈𝐍𝐓𝐄𝐑𝐕𝐀𝐋 : Min. : 8 hours Max.: 24 hours
𝐂𝐎𝐌𝐏𝐀𝐓𝐈𝐁𝐈𝐋𝐈𝐓𝐘 : Can be applied over Epoxy and Polyurethane primers, intermediated coats
and topcoats
Application Method
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio by volume. Stir the mix gently to attain homogeneity. Add thinner type 001 into the mix, if required depending on the application method and then stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Strain the paint through Nylon filter cloth 400 mesh size and apply uniformly over the surface. All equipments used for above should be properly clean.
Application : By Brush / By Conventional / By Airless Spray
For Brush application, generally no thinner is required to be added. However under adverse environmental condition about 5% by volume thinner can be added. Apply evenly in crossed manner and ensure the uniformity. Use quality brushes for paint application.
For Conventional Spray application
Thinner : Type 001
Addition : 5 – 15%
Nozzle Orifice : 1.2mm – 1.4mm
Nozzle Pressure : 40 – 70 p.s.i.
For Airless Spray application
Thinner : Type 001
Addition : Max 5% if required
Nozzle Orifice : 0.28mm
Nozzle Pressure : 1400 – 1800 p.s.i.
Notes
1. Do not apply paint when temperature falls below 10® C or rises above 50® C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3 ® C above Dew point.
2. Brushes and spray equipment should be cleaned with KP’s recommended thinner otherwise equipment is liable to be damaged.
3. Volume Solids will vary depending on shades. Products with different volume solids are also available on request.
4. DFT variation can be obtained by change in application method / thinning ratio. Contact Khodal Paints representatives for further assistance.
5. Shelf life indicated is minimum for this Prodcut in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition away.
Health & Safety
This is a solvent based paint and care should be taken to avoid inhalation of spray or eyes. Mist or vapours as well as contact between the wet paint and exposed skin.
Limitation of Liability
To the best of our knowledge the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to confirm to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.
