Zinc Phosphate Grey
Slide

Description

Two components Epoxy based anti corrosive primer containing zinc phosphate as corrosion inhibiting pigments.
Faux Finishes
Slide

Recommended Use

It is recommended as primer on M. S. Surface for OEM’s as well as for process industries like fertilizers, refineries, chemicals and other plants. It can also be applied in diverse areas of tank exteriors, equipments, pipelines, structural steel , etc,. Not to be used for immersion application.

Faux Finishes
Slide

Physical Data

COLOR : Assorted
FINISH : Matt
SOLIDS BY VOLUME : 40 + 3%
THEORETICAL SPREADING RATE : 13.33 sq. mt./ltr. at recommended DFT of 30 µ
FLASH POINT : Base
Above 23® C Hardener : Above 23® C
DRYING CHARACTERISTICS : Surface Dry : 60 – 90 minutes(At 65% relative humidity & at 30® C)
Hard Dry : Overnight
Full Cure : 7 Days
SHELL LIFE : Base : 6 months
Hardener : 6 months
Faux Finishes
Slide

Surface Preperation

Abrasive blasting to Sa 2 1/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moist and oil free before primer application.
Faux Finishes
Slide

Application Data

MIXING RATIO : Base : Hardener – (As per our recommendations)
APPLICATION : By Brush / By Conventional Spray / By Airless Spray
THINNER : Type 002
POT LIFE : 4 hours min at 30® C
RECOMMENDED DFT : 30 – 40 µ. OVERCOATING INTERVAL :
Min. : 8 hours
Max. : 24 hours
COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats
Faux Finishes
Slide

Application Method

Stir the base part thoroughly with. Mix the base and hardener as per our recommended ratio by volume. Stir the mix genlty to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add thinner type 002 into the mix, if required depending on the application method and then stir gently for few minutes. Strain the paint throught Nylon filter cloth of 100 mesh size and apply uniformly over the surface. All equipment used for above should be properly cleaned.
Faux Finishes

Application : By Brush / By Conventional Spray / By Airless Spray

Generally no thinner is reqired for Brush application, however under adverse enviornmental conditions about 5% thinner by volume. Apply evenly in crossed manner ensuring the uniform application. Use quality brushes for paint application.

For Conventional Spray application:

Thinner : Type 002
Addition : 10-15%
Nozzle Orifice : 1.2 – 1.4mm
Nozzle Pressure: 40 – 70 p.s.i.

For Airless Spray application

Thinner : Type 002
Addition : Max 5% if required
Nozzle Orifice : 0.37mm – 0.42mm
Nozzle Pressure : 2 100 -2400 p.s.i.

Notes

1. Do not apply paint when temperature falls below 10® C or rises above 50® C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3 ® C above Dew point.
2. Brushes and spray equipment should be cleaned with KP’s recommended thinner otherwise equipment is liable to be damaged.
3. Products with different volume solids, with Amine Hardner and also Ld/Crfree version are available on requests.
4. Product for flow coat applications is also available on request.
5. DFT variation can be obtained by change in application method / thinning ratio. Contact Khodal Paints representatives for further assistance.
6. Shelf life indicated is minimum for this Prodcut in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition away from heat and ignition.

Health & Safety

This is a solvent based paint and care should be taken to avoid inhalation of spray or eyes. Mist or vapours as well as contact between the wet paint and exposed skin.

Limitation of Liability

To the best of our knowledge the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to confirm to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any is limited to replacment of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.