Product Description:
A single pack of Rama HR 600 high performance heat resistant aluminum paint based on silicone resin medium for protection of steel surface operating between 400® C – 600® C dry heat.
Physical Data:
𝐂𝐎𝐋𝐎𝐑 : Aluminum𝐅𝐈𝐍𝐈𝐒𝐇 : Bright Metallic
𝐒𝐎𝐋𝐈𝐃𝐒 𝐁𝐘 𝐕𝐎𝐋𝐔𝐌𝐄 : 18% (Approx.)
𝐓𝐇𝐄𝐎𝐑𝐄𝐓𝐈𝐂𝐀𝐋 𝐒𝐏𝐑𝐄𝐀𝐃𝐈𝐍𝐆 𝐑𝐀𝐓𝐄 : 12.0 – 9.0 Sq.metre per litre
𝐅𝐋𝐀𝐒𝐇 𝐏𝐎𝐈𝐍𝐓 : Above 23® C
𝐃𝐑𝐘𝐈𝐍𝐆 𝐂𝐇𝐀𝐑𝐀𝐂𝐓𝐄𝐑𝐈𝐒𝐓𝐈𝐂𝐒 : Dust Free – 4 hours
𝐒𝐇𝐄𝐋𝐋 𝐋𝐈𝐅𝐄 :12 months
𝐂𝐎𝐑𝐑𝐄𝐒𝐏𝐎𝐍𝐃𝐈𝐍𝐆 𝐖𝐄𝐓 𝐅𝐈𝐋𝐌 𝐓𝐇𝐈𝐂𝐊𝐍𝐄𝐒𝐒 : 83-111 microns
𝐑𝐄𝐂𝐎𝐌𝐌𝐄𝐍𝐃𝐄𝐃 𝐃𝐑𝐘 𝐅𝐈𝐋𝐌 𝐓𝐇𝐈𝐂𝐊𝐍𝐄𝐒𝐒 : 15 – 20 microns per coat
𝐈𝐍𝐓𝐄𝐑𝐕𝐀𝐋 𝐁𝐄𝐅𝐎𝐑𝐄 𝐎𝐕𝐄𝐑𝐂𝐎𝐀𝐓𝐈𝐍𝐆 : Minimum – 18 hours Maximum – Indefinite
𝐃𝐑𝐘 𝐇𝐄𝐀𝐓 𝐑𝐄𝐒𝐈𝐒𝐓𝐀𝐍𝐂𝐄 : Upto 400® C – 600® C (Continuous)
Surface Preperation:
Degrease and blast clean to Sa 2 ½ grade minimum of Swedish specification SIS – 05 – 5900 – 1967. If blast cleaning is not practical make full use of mechanical tools along with manual cleaning and wire brushing to remove loose rust / scale to St 2 or St 3 grade of Swedish specification. Surface should be perfectly clean and dry before application of RAMA HR 600.
Application Data:
𝐀𝐏𝐏𝐋𝐈𝐂𝐀𝐓𝐈𝐎𝐍 : By Conventional / By Brush𝐓𝐇𝐈𝐍𝐍𝐄𝐑 : Type 006
𝐃𝐑𝐘𝐈𝐍𝐆 𝐓𝐈𝐌𝐄 : Touch dry 4 – 6 hours
Curing :
Apply 1st coat. Air dry for 24 hours. Alternatively eat cure at 200® C for 1 hour after 4 hours of air drying. Apply 2nd coat. Allow it to dry overnight and then gradually raise the temperature to working temperature
Mixing :
Aluminum paste and medium supplied in proportionate quantities. Mix the contents thoroughly and stir well before and during application. Mixed paint to be used off within 24 hours to maintain uniformity in Rama HR 400.
Uses:
For Painting of Chimney, Flare Stacks, Exhausts, Pipe Works, Incinerators and similar surfaces exposed to dry heat attack etc.
Storage Life:
Upto 12 months so long as the material is stored in sealed containers under standard warehouse storage conditions.
Application Method
Stir the Base part thoroughly. Mix the 5 -10% Thinner in the paint as per our recommended ratio by volume. Stir the mix gently to attain homogeneity. Add thinner into the mix, if required depending on the application method and then stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Strain the paint through Nylon filter cloth 400 mesh size and apply uniformly over the surface. All equipments used for above should be properly clean.
Application : By Brush / By Conventional Spray
For Brush application, generally no thinner is required to be added. However under adverse environmental condition about 5% by volume thinner can be added. Apply evenly in crossed manner and ensure the uniformity. Use quality brushes for paint application.
For Conventional Spray application
Thinner : Type 006
Addition : 5 – 15%
Nozzle Orifice : 1.2mm – 1.5mm
Nozzle Pressure : 45 – 55 p.s.i.
Notes:
Health & safety:
Please refer to the separate safety data sheet available with detailed information.
Limitation of Liability
To the best of our knowledge the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to confirm to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages
are hereby excluded
